LS XBM Cnet Serial (Gen1)

review the following information for setting up and configuring the ls xbm cnet serial (gen1) driver litmus edge compatible series compatibility parameter compatible items driver type serial validated devices/series ls electric xbm series with communication module xgl ch2a to set up and configure this device in litmus edge, you will need to do the following step 1 set up and configure the plc device step 2 set up the plc device in litmus edge devicehub step 3 configure the list of registers step 1 set up and configure the plc device record the serial communication parameters for the device otherwise, use plc software on your machine to look up these parameters you use these parameters for setting up the driver in the next step step 2 set up the plc device in litmus edge devicehub configure the following parameters when you docid\ pal6abpzbrimdu9lvgj30 with this driver update default values to the specific setup of your device parameter value type ls industrial system driver ls xbm cnet serial (gen1) communication port local serial connection file path data bits 8 baud rate 115200 parity even, odd, none stop bits 1 station id 1 step 3 configure the list of registers when you docid 8se7z3pmrfwl1nmzcwalx to the connected device, refer to the following register table and tag parameters refer to the following additional resources docid 583p fbuozem6whgrdgkq docid\ ifbwcou90qtfodk hrysr register table name value types address format min address max address description pw bit bit dddddd 0 204715 i/o device bit mw bit bit dddddd 0 204715 internal device bit lw bit bit ddddddd 0 1126316 communication device bit kw bit bit dddddd 0 255915 preservation device bit fw bit bit dddddd 0 204715 special device bit dw bit bit ddddddd 0 3276715 data register bit uw bit bit dddddd 0 633115 rw bit bit ddddddd 0 3276715 sx bit ddddd 0 12799 relay for step control bit tx bit dddd 0 2047 timer device bit cx bit dddd 0 2047 counter device bit pw word dddd 0 2047 i/o device mw word dddd 0 2047 internal device lw word ddddd 0 11263 communication device kw word dddd 0 2559 preservation device fw word dddd 0 2047 special device sw word ddd 0 127 relay for step control dw word ddddd 0 32767 data register uw word dddd 0 6331 analog data register nw word ddddd 0 21503 communiction data register zw word ddd 0 127 index register tw word dddd 0 2047 timer current value cw word dddd 0 2047 counter current value rw word ddddd 0 32767 tag parameters name select a register name from the drop down list the available options depend on the names in the register table value type select a data type from the drop down list the available options depend on the register name selected polling interval enter a value in seconds this determines how often the tag should poll the register for data tag name enter a name for the tag description (optional) enter a description for the tag address enter a tag address the value must in the decimal format, within the allowed min/max range omit the leading zeros the device might use the decimal (d), hexadecimal (h), or octal (o) address format see the register table at the bottom of the dialog box for bit tags, append the bit address without the bit separator the lowercase letters in the address format indicate how many digits you should enter in the bit address tag formula enter a formula for the tag to process the generated data two variables are permitted value (current tag value) and timestamp (current tag unix time in milliseconds) the following math functions are available sin cos sqrt tan power power( x ) performs the operation 10^x log log( x ) is the natural logarithm (the logarithm is in base e ) exp exp( x ) performs the operation e^x only publish on change of value select the checkbox to only publish nats messages when the value parameter changes to a new value change of value only applies to boolean, numeric (such as int or float), and simple string data types it does not apply to complex types, such as json or array poll once topics will not be affected by change of value settings these topics will still only see a single message meta data metadata summarizes basic information about data this feature allows you to define key value pair data for the device output payload later on metadata can then be used to find, use, and reuse particular instances of data note if you use special characters in meta data key names, the special characters are replaced with underscore characters in the payload this can cause two key names to be combined into one for example, configuring the key names a b and a&\&b will cause only one key name to be created (a b)