ABB Totalflow DB2 (Gen1.3)

review the following information for setting up and configuring the abb totalflow db2 (gen1 3) driver litmus edge compatible series compatibility parameter compatible items driver type ethernet validated devices/series https //new\ abb com/products/measurement products/upstream oil and gas/flow computers remote controllers/flow computers https //new\ abb com/products/measurement products/upstream oil and gas/flow computers remote controllers/flow computers https //new\ abb com/products/measurement products/upstream oil and gas/flow computers remote controllers/flow computers https //new\ abb com/products/measurement products/upstream oil and gas/flow computers remote controllers/flow computers the https //new\ abb com/products/robotics/controllers/irc5 overview/irc5 device is not compatible with this driver as an alternative, you can connect through an opc ua server to set up and configure this device in litmus edge, you will need to do the following step 1 set up and configure the plc device step 2 set up the plc device in devicehub step 3 configure the list of registers step 1 set up and configure the plc device if the device is configured for ethernet access, find its network parameters otherwise, use plc software on your computer to configure the device for ethernet access step 2 set up the plc device in litmus edge devicehub configure the following parameters when you docid\ pal6abpzbrimdu9lvgj30 with this driver update default values to the specific setup of your device parameter value type abb driver abb totalflow db2 (gen1 3) network address the device address you defined during step 1 network port 9999 step 3 configure the list of registers when you docid\ tuy hh0gi8djvot70wroh to the connected device, see the following register table and tag parameters sections you can also docid 8oruw1cmtao49bwbbhwrn for the device see the following additional resources if necessary docid\ mu 6j6zhi0cvchdad0w8n docid\ io7xgyrdvv vmpnfxoaci register table the register table addresses follow the format \<application> \<array> \<register> when entering the address in devicehub, add left padding zeros and remove the period delimiters find the list of registers in the https //library e abb com/public/f767e1b1766dfa26c1257b1a005b0e6b/xrc%20manual%20aa pdf name value types address format min address max address bit bit tttfffdddd 0 2552553647 w bit bit tttfffdddddd 0 255255364715 byte byte, sint tttfffdddd 0 2552553647 word word, int, dword, dint, float, double, lword, lint tttfffdddd 0 2552553647 dword dword, dint, float, double, lword, lint tttfffdddd 0 2552553647 string string tttfffdddd 0 2552553647 tag parameters name select a register name from the drop down list available options depend on the names in the register table value type select a data type from the drop down list available options depend on the register name selected polling interval enter a value in seconds this determines how often the tag should poll the register for data tag name enter a name for the tag description (optional) enter a description for the tag address enter a tag address the value must in the decimal format within the allowed min/max range omit the leading zeros the device might use the decimal (d), hexadecimal (h), or octal (o) address format see the register table at the bottom of the dialog box for bit tags, append the bit address without the bit separator the lowercase letters in the address format indicate how many digits you should enter in the bit address count enter the number of register values to read a count higher than 1 will generate an array of values from the address value configured and respective subsequent address values tag formula enter a formula for the tag to process the generated data two variables are permitted value (current tag value) and timestamp (current tag unix time in milliseconds) the following math functions are available sin cos sqrt tan power power( x ) performs the operation 10^x log log( x ) is the natural logarithm (the logarithm is in base e ) exp exp( x ) performs the operation e^x only publish on change of value select the checkbox to publish nats messages only when the value parameter changes to a new one value change of value only applies to boolean, numeric (such as int or float), and simple string data types it does not apply to complex types, such as json or array poll once topics are not affected by change of value settings these topics will still only see a single message meta data metadata summarizes basic information about data this feature allows you to define key value pair data for the device output payload later on it can then be used to find, use, and reuse particular instances of data note if you use special characters in meta data key names, the special characters are replaced with underscore characters in the payload this can cause two key names to be combined into one for example, configuring the key names a b and a&\&b will cause only one key name to be created (a b)