Mitsubishi QJ71E71

review the following information for setting up and configuring the mitsubishi qj71e71 driver note we recommend the docid\ af6ut40eqjqt35y6enwnr driver to connect to qj71e71 modules, because it has more efficient communication with the plc and supports more data types litmus edge compatible series compatibility parameter compatible items driver type ethernet validated devices/series https //www mitsubishielectric com/fa/products/cnt/plcq/items/index html replaces gen 1 driver(s) docid\ oq2ntmqi dhjjf9ge7tdz to set up and configure this device in litmus edge, you will need to do the following step 1 set up and configure the plc device step 2 set up the plc device in litmus edge devicehub step 3 configure the list of registers step 1 set up and configure the plc device if the device is configured for ethernet access, find its network parameters otherwise, use gx works2 v1 560j software on your computer to configure the device for ethernet access note only one connection is allowed per port defined in the plc step 2 set up the plc device in litmus edge devicehub configure the following parameters when you docid\ pal6abpzbrimdu9lvgj30 with this driver update default values to the specific setup of your device parameter value type mitsubishi driver mitsubishi qj71e71 network address the device address you defined in step 1 port 5002 station id 1 step 3 configure the list of registers when you docid 8se7z3pmrfwl1nmzcwalx to the connected device, refer to the following register table and tag parameters refer to the following additional resources docid 583p fbuozem6whgrdgkq docid\ ifbwcou90qtfodk hrysr register table name value types address format min address max address description b bit ddddd 0 32237 link relay cc bit ddddd 0 25471 counter coil cs bit ddddd 0 25471 counter contact dx bit dddd 0 8191 direct input dy bit dddd 0 8191 direct output f bit ddddd 0 32237 annunciator l bit ddddd 0 32237 latch relay m bit ddddd 0 65535 internal relay s bit dddd 0 8191 step relay sb bit ddddd 0 32237 special link relay sm bit dddd 0 2047 special relay stc bit ddddd 0 25471 retentive timer coil sts ddddd 0 25471 retentive timer current value tc bit ddddd 0 25471 timer coil ts bit ddddd 0 25471 timer contact v bit ddddd 0 32237 edge relay x bit ddddd 0 65535 input relay y bit ddddd 0 65535 output relay cn word dddd 0 1023 counter current d word dddd 0 9999 data register r word dddd 0 9999 file register sd word dddd 0 2047 special register stn word ddddd 0 25471 retentive timer current value tn word ddddd 0 25471 timer current value w word dddd 0 8191 link register z word dd 0 20 index register zr word dddddd 0 999999 file register tag parameters name select a register name from the drop down list available options depend on the names in the register table value type select a data type from the drop down list available options depend on the register name selected polling interval enter a value in seconds this determines how often the tag should poll the register for data tag name enter a name for the tag description (optional) enter a description for the tag address enter a tag address the value must in the decimal format within the allowed min/max range omit the leading zeros the device might use the decimal (d), hexadecimal (h), or octal (o) address format see the register table at the bottom of the dialog box for bit tags, append the bit address without the bit separator the lowercase letters in the address format indicate how many digits you should enter in the bit address count enter the number of register values to read a count higher than 1 will generate an array of values from the address value configured and respective subsequent address values tag formula enter a formula for the tag to process the generated data two variables are permitted value (current tag value) and timestamp (current tag unix time in milliseconds) the following math functions are available sin cos sqrt tan power power( x ) performs the operation 10^x log log( x ) is the natural logarithm (the logarithm is in base e ) exp exp( x ) performs the operation e^x only publish on change of value select the checkbox to publish nats messages only when the value parameter changes to a new one value change of value only applies to boolean, numeric (such as int or float), and simple string data types it does not apply to complex types, such as json or array poll once topics are not affected by change of value settings these topics will still only see a single message meta data metadata summarizes basic information about data this feature allows you to define key value pair data for the device output payload later on it can then be used to find, use, and reuse particular instances of data note if you use special characters in meta data key names, the special characters are replaced with underscore characters in the payload this can cause two key names to be combined into one for example, configuring the key names a b and a&\&b will cause only one key name to be created (a b)