Omron Fins Ethernet (Gen1)

review the following information for setting up and configuring the omron fins ethernet (gen1) driver litmus edge compatible series compatibility parameter compatible items driver type ethernet validated devices/series https //www ia omron com/products/category/automation systems/programmable controllers/cj1/index html https //www ia omron com/products/category/automation systems/programmable controllers/cj2/index html https //www ia omron com/products/category/automation systems/programmable controllers/cs1/index html replaced with gen 2 driver docid\ s y 9lbr8yaun0wdy1be to set up and configure this device in litmus edge, you will need to do the following step 1 set up and configure the plc device step 2 set up the plc device in litmus edge devicehub step 3 configure the list of registers step 1 set up and configure the plc device if the device is configured for ethernet access, find its network parameters otherwise, follow the steps below to configure your device record the following information and refer to it as needed device omron cj2m cpu15 communication i/f ethernet refer to the following figure connect the pc to the device using usb cable launch cx programmer and create a project click plc > work online open io table and unit setting and create io table based on hardware allocation set up communication parameters for communication module transfer to plc log in using ethernet, click offline , and then click the device name select ethernet as the network type, click settings , set up the ip and port number, and then click plc > work online step 2 set up the plc device in litmus edge devicehub configure the following parameters when you docid\ pal6abpzbrimdu9lvgj30 with this driver update default values to the specific setup of your device parameter value type omron driver omron fins ethernet (gen1) network address the device address you defined during step 1 port 9600 step 3 configure the list of registers when you docid\ tuy hh0gi8djvot70wroh to the connected device, refer to the following register table and tag parameters see the following additional resources if necessary docid\ mu 6j6zhi0cvchdad0w8n docid\ io7xgyrdvv vmpnfxoaci register table name value types address format min address max address description cio bit bit ddddddd 0 3276715 channel i/o bit cio word, string ddddd 0 32767 channel i/o w word, string ddddd 0 32767 work area a word, string ddddd 0 32767 auxiliary relay h word, string ddddd 0 32767 holding area c word, string ddddd 0 32767 counter t word, string ddddd 0 32767 timer d word, string ddddd 0 32767 data memory em0 word, string ddddd 0 32767 extended memory em1 word, string ddddd 0 32767 extended memory em2 word, string ddddd 0 32767 extended memory em3 word, string ddddd 0 32767 extended memory tag parameters name select a register name from the drop down list available options depend on the names in the register table value type select a data type from the drop down list available options depend on the register name selected polling interval enter a value in seconds this determines how often the tag should poll the register for data tag name enter a name for the tag description (optional) enter a description for the tag address enter a tag address the value must in the decimal format within the allowed min/max range omit the leading zeros the device might use the decimal (d), hexadecimal (h), or octal (o) address format see the register table at the bottom of the dialog box for bit tags, append the bit address without the bit separator the lowercase letters in the address format indicate how many digits you should enter in the bit address count enter the number of register values to read a count higher than 1 will generate an array of values from the address value configured and respective subsequent address values tag formula enter a formula for the tag to process the generated data two variables are permitted value (current tag value) and timestamp (current tag unix time in milliseconds) the following math functions are available sin cos sqrt tan power power( x ) performs the operation 10^x log log( x ) is the natural logarithm (the logarithm is in base e ) exp exp( x ) performs the operation e^x only publish on change of value select the checkbox to publish nats messages only when the value parameter changes to a new one value change of value only applies to boolean, numeric (such as int or float), and simple string data types it does not apply to complex types, such as json or array poll once topics are not affected by change of value settings these topics will still only see a single message meta data metadata summarizes basic information about data this feature allows you to define key value pair data for the device output payload later on it can then be used to find, use, and reuse particular instances of data note if you use special characters in meta data key names, the special characters are replaced with underscore characters in the payload this can cause two key names to be combined into one for example, configuring the key names a b and a&\&b will cause only one key name to be created (a b)