Siemens Logo Ethernet (Gen1.3)

review the following information for setting up and configuring the siemens logo ethernet (gen1 3) driver litmus edge compatible series compatibility parameter compatible items driver type ethernet validated devices/series siemens logo! to set up and configure this device in litmus edge, you will need to do the following step 1 set up and configure the plc device step 2 set up the plc device in litmus edge devicehub step 3 configure the list of registers step 1 set up and configure the plc device if the device is configured for ethernet access, find its network parameters otherwise, follow the steps below to configure your device note down the following information and refer to it when needed device logo bm 24ce communication i/f ethernet refer to the following figure set up the ip address under admin mode the default password to switch from operator mode is logo select network > ip address enter the ip address for your device for example 192 168 447 110 log in to the web server to configure the device the default password is logo launch the logo soft comfort v1 08 02 software and select tools > transfer > logo > pc enter the ip address in the target ip address field, and then click ok select tools > ethernet connection from the configure ethernet connection dialog box, click ethernet connectors from the local properties (server) section, select accept all connection results from the remote properties (client) section, enter the local tsap in the tsap field the local tsap default is 20 00 for this configuration, the remote tsap is set to 21 00 click ok step 2 set up the plc device in litmus edge devicehub configure the following parameters when you connect a device docid\ pal6abpzbrimdu9lvgj30 with this driver update default values to the specific setup of your device parameter value type siemens driver siemens logo ethernet (gen1 3) network address the device address you defined during step 1 port 102 local tsap 4096 remote tsap 512 step 3 configure the list of registers when you add a tag docid\ tuy hh0gi8djvot70wroh to the connected device, refer to the following register table and tag parameters see the following additional resources if necessary organize device and tag data by using metadata docid\ mu 6j6zhi0cvchdad0w8n tag formula variables docid\ io7xgyrdvv vmpnfxoaci register table name value types address format min address max address description i bit dd 1 64 input bit q bit dd 1 64 output bit m bit ddd 1 112 ni bit ddd 1 128 nq bit ddd 1 128 v bit ddddo 0 14697 ai word dd 1 16 analog input aq word dd 1 16 analog output am word dd 1 64 nai word dd 1 64 naq word dd 1 32 vb byte dddd 0 1469 vw word dddd 0 1468 vd dword dddd 0 1466 rtc word d 1 7 tag parameters name select a register name from the drop down list the available options depend on the names in the register table value type select a data type from the drop down list the available options depend on the register name selected polling interval enter a value in seconds this determines how often the tag should poll the register for data tag name enter a name for the tag description (optional) enter a description for the tag address enter a tag address the value must in the decimal format, within the allowed min/max range omit the leading zeros the device might use the decimal (d), hexadecimal (h), or octal (o) address format see the register table at the bottom of the dialog box for bit tags, append the bit address without the bit separator the lowercase letters in the address format indicate how many digits you should enter in the bit address tag formula enter a formula for the tag to process the generated data two variables are permitted value (current tag value) and timestamp (current tag unix time in milliseconds) the following math functions are available sin cos sqrt tan power power( x ) performs the operation 10^x log log( x ) is the natural logarithm (the logarithm is in base e ) exp exp( x ) performs the operation e^x only publish on change of value select the checkbox to only publish nats messages when the value parameter changes to a new value change of value only applies to boolean, numeric (such as int or float), and simple string data types it does not apply to complex types, such as json or array poll once topics will not be affected by change of value settings these topics will still only see a single message meta data metadata summarizes basic information about data this feature allows you to define key value pair data for the device output payload later on metadata can then be used to find, use, and reuse particular instances of data note if you use special characters in meta data key names, the special characters are replaced with underscore characters in the payload this can cause two key names to be combined into one for example, configuring the key names a b and a&\&b will cause only one key name to be created (a b)