Toshiba Computer Link Ethernet (Gen1).3

review the following information for setting up and configuring the toshiba computer link ethernet (gen1 3) driver litmus edge compatible series compatibility parameter compatible items driver type ethernet validated devices/series any of the following toshiba series models with an ethernet module s2 s3 t2 t3 to set up and configure this device in litmus edge, you will need to do the following step 1 set up and configure the plc device step 2 set up the plc device in litmus edge devicehub step 3 configure the list of registers step 1 set up and configure the plc device if the device is configured for ethernet access, find its network parameters otherwise, use plc software on your computer to configure your device for ethernet access step 2 set up the plc device in litmus edge devicehub configure the following parameters when you connect a device docid\ pal6abpzbrimdu9lvgj30 with this driver update default values to the specific setup of your device parameter value type toshiba driver toshiba computer link ethernet (gen1 3) network address the device address you defined in step 1 network port 1024 step 3 configure the list of registers when you add a tag docid\ tuy hh0gi8djvot70wroh to the connected device, refer to the following register table and tag parameters see the following additional resources if necessary organize device and tag data by using metadata docid\ mu 6j6zhi0cvchdad0w8n tag formula variables docid\ io7xgyrdvv vmpnfxoaci register table name value types address format min address max address description x bit dddddd 0 511915 input devices i bit dddddd 0 511915 direct input devices y bit dddddd 0 511915 output devices o bit dddddd 0 511915 direct output devices r bit dddddd 0 409515 auxiliary devices dbit bit dddddd 0 409515 auxiliary devices s bit ddddd 0 51115 special devices xw word,short,dword,long,float dddd 0 5119 input registers iw word,short,dword,long,float dddd 0 5119 direct input registers yw word,short,dword,long,float dddd 0 5119 output registers ow word,short,dword,long,float dddd 0 5119 direct output registers rw word,short,dword,long,float dddd 0 4095 auxiliary registers dw word,short,dword,long,float dddd 0 5119 auxiliary registers sw word,short,dword,long,float ddd 0 511 special registers d word,short,dword,long,float dddd 0 4095 data memory dh string dddd 0 4095 data memory as string with hilo byte order dl string dddd 0 4095 data memory as string with lohi byte order tag parameters name select a register name from the drop down list available options depend on the names in the register table value type select a data type from the drop down list available options depend on the register name selected polling interval enter a value in seconds this determines how often the tag should poll the register for data tag name enter a name for the tag description (optional) enter a description for the tag address enter a tag address the value must in the decimal format within the allowed min/max range omit the leading zeros the device might use the decimal (d), hexadecimal (h), or octal (o) address format see the register table at the bottom of the dialog box for bit tags, append the bit address without the bit separator the lowercase letters in the address format indicate how many digits you should enter in the bit address count enter the number of register values to read a count higher than 1 will generate an array of values from the address value configured and respective subsequent address values tag formula enter a formula for the tag to process the generated data two variables are permitted value (current tag value) and timestamp (current tag unix time in milliseconds) the following math functions are available sin cos sqrt tan power power( x ) performs the operation 10^x log log( x ) is the natural logarithm (the logarithm is in base e ) exp exp( x ) performs the operation e^x only publish on change of value select the checkbox to publish nats messages only when the value parameter changes to a new one value change of value only applies to boolean, numeric (such as int or float), and simple string data types it does not apply to complex types, such as json or array poll once topics are not affected by change of value settings these topics will still only see a single message meta data metadata summarizes basic information about data this feature allows you to define key value pair data for the device output payload later on it can then be used to find, use, and reuse particular instances of data note if you use special characters in meta data key names, the special characters are replaced with underscore characters in the payload this can cause two key names to be combined into one for example, configuring the key names a b and a&\&b will cause only one key name to be created (a b)