LS XBM Cnet Serial (Gen1.3)

6 min

Review the following information for setting up and configuring the LS XBM Cnet Serial (Gen1.3) driver.

Litmus Edge Compatible Series

Compatibility parameter	Compatible items
Driver type	Serial
Validated devices/series	LS Electric XBM Series with communication module XGL-CH2A

To set up and configure this device in Litmus Edge, you will need to do the following:

Step 1: Set up and Configure the PLC Device

Step 2: Set up the PLC Device in Litmus Edge DeviceHub

Step 3: Configure the List of Registers

Step 1: Set up and Configure the PLC Device

Record the serial communication parameters for the device. Otherwise, use PLC software on your machine to look up these parameters. You use these parameters for setting up the driver in the next step.

Step 2: Set up the PLC Device in Litmus Edge DeviceHub

Configure the following parameters when you Connect a Device with this driver. Update default values to the specific setup of your device.

Parameter	Value
Type	LS Industrial System
Driver	LS XBM Cnet Serial (Gen1.3)
Communication Port	Local Serial connection file path
Data Bits	8
Baud Rate	115200
Parity	Even, Odd, None
Stop Bits	1
Station ID	1

Step 3: Configure the List of Registers

When you Add a Tag to the connected device, see the following Register Table and Tag Parameters sections.

See the following additional resources if necessary:

Organize Device and Tag Data by Using Metadata

Tag Formula Variables

Register Table

Name	Value Types		Address Format	Max Address	Description
PW_bit	bit	R/W	DDDDdd	204715	I/O device bit
MW_Bit	bit	R/W	DDDDdd	204715	Internal device bit
LW_Bit	bit	R/W	DDDDDdd	1126316	Communication device bit
KW_Bit	bit	R/W	DDDDdd	255915	Preservation device bit
FW_Bit	bit	R/W	DDDDdd	204715	Special device bit
DW_Bit	bit	R/W	DDDDDdd	3276715	Data register bit
UW_Bit	bit	R/W	DDDDdd	633115
RW_Bit	bit	R/W	DDDDDdd	3276715
SX	bit	R/W	DDDDD	12799	Relay for step control bit
TX	bit	R/W	DDDD	2047	Timer device bit
CX	bit	R/W	DDDD	2047	Counter device bit
PW	word	R/W	DDDD	2047	I/O device
MW	word	R/W	DDDD	2047	Internal device
LW	word	R/W	DDDDD	11263	Communication device
KW	word	R/W	DDDD	2559	Preservation device
FW	word	R/W	DDDD	2047	Special device
SW	word	R/W	DDD	127	Relay for step control
DW	word	R/W	DDDDD	32767	Data register
UW	word	R/W	DDDD	6331	Analog data register
NW	word	R/W	DDDDD	21503	Communiction data register
ZW	word	R/W	DDD	127	Index register
TW	word	R/W	DDDD	2047	Timer current value
CW	word	R/W	DDDD	2047	Counter current value
RW	word	R/W	DDDDD	32767

Tag Parameters

Name: Select a register name from the drop-down list. The available options depend on the names in the register table.

Value Type: Select a data type from the drop-down list. The available options depend on the register name selected.

Polling Interval: Enter a value in seconds. This determines how often the tag should poll the register for data.

Tag Name: Enter a name for the tag.

Description (Optional): Enter a description for the tag.

Address: Enter a tag address. The value must in the decimal format, within the allowed min/max range. Omit the leading zeros. The device might use the decimal (D), hexadecimal (H), or octal (O) address format. See the Register Table at the bottom of the dialog box. For Bit tags, append the bit address without the bit separator. The lowercase letters in the address format indicate how many digits you should enter in the Bit address.

Tag Formula: Enter a formula for the tag to process the generated data. Two variables are permitted: value (current tag value) and timestamp (current tag UNIX time in milliseconds). The following math functions are available:

sqrt

power: power(x) performs the operation 10^x.

log: log(x) is the natural logarithm (the logarithm is in base e).

exp: exp(x) performs the operation e^x.

Only Publish on Change of Value: Select the checkbox to only publish NATS messages when the value parameter changes to a new value. Change of Value only applies to boolean, numeric (such as int or float), and simple string data types. It does not apply to complex types, such as JSON or array. Poll-once topics will not be affected by Change of Value settings. These topics will still only see a single message.

Meta Data: Metadata summarizes basic information about data. This feature allows you to define key-value pair data for the device output payload later on. Metadata can then be used to find, use, and reuse particular instances of data.

Note: If you use special characters in meta data key names, the special characters are replaced with underscore characters in the payload. This can cause two key names to be combined into one. For example, configuring the key names a**b and a&&b will cause only one key name to be created (a__b).