Mitsubishi FX5U-Ethernet-Binary (Gen1.3)

review the following information for setting up and configuring the mitsubishi fx5u ethernet binary (gen1 3) driver litmus edge compatible series compatibility parameter compatible items driver type ethernet validated devices/series https //www mitsubishielectric com/fa/products/cnt/plcf/items/index html to set up and configure this device in litmus edge, you will need to do the following step 1 set up and configure the plc device step 2 set up the plc device in litmus edge devicehub step 3 configure the list of registers step 1 set up and configure the plc device note only one connection is allowed per port defined in the plc see the steps below to view and edit the open ports on the plc if the device is configured for ethernet access, find its network parameters otherwise, follow the steps below to configure your device note down the following information and refer to it when needed device mitsubishi fx5u ethernet binary fx5u 32m communication i/f ethernet refer to the following figure launch gxwork3 v1 035m software, and then click online > read from plc select the series select the connection destination double click the plc module icon, and click find to browse the device on the network from the navigation panel, click ethernet port to set up communication parameters use binary for this device double click external device configuration set up the connections in this case, port 4996 through 4999 are able to connect step 2 set up the plc device in litmus edge devicehub configure the following parameters when you docid\ pal6abpzbrimdu9lvgj30 with this driver update default values to the specific setup of your device parameter value type mitsubishi driver 3mitsubishi fx5u ethernet binary (gen1 ) network address the device address you defined in step 1 port 5002 station id 255 step 3 configure the list of registers when you docid\ tuy hh0gi8djvot70wroh to the connected device, refer to the following register table and tag parameters see the following additional resources if necessary docid\ mu 6j6zhi0cvchdad0w8n docid\ io7xgyrdvv vmpnfxoaci register table name value type address format min address max address description sm bit dddd 0 9999 special relay x bit hhhh 0 1023 input relay y bit hhhh 0 1023 output relay m bit ddddd 0 65535 internal relay l bit ddddd 0 32237 latch relay f bit ddddd 0 32237 annunciator b bit ddddd 0 32237 link relay ts bit dddd 0 1023 timer contact tc bit dddd 0 1023 timer coil cs bit dddd 0 1023 counter contact cc bit dddd 0 1023 counter coil sb bit ddddd 0 32737 special link relay s bit dddd 0 4095 step relay z word dd 0 19 index register sw word ddddd 0 32767 specail link register cn word dddd 0 1023 counter current value sn word dddd 0 1023 retentive timer current value tn word dddd 0 1023 timer current value w word ddddd 0 32767 link relgister r word ddddd 0 32767 file register d word dddd 0 7999 data register sd word ddddd 0 11999 special register lz word d 0 1 long index register tag parameters name select a register name from the drop down list the available options depend on the names in the register table value type select a data type from the drop down list the available options depend on the register name selected polling interval enter a value in seconds this determines how often the tag should poll the register for data tag name enter a name for the tag description (optional) enter a description for the tag address enter a tag address the value must in the decimal format, within the allowed min/max range omit the leading zeros the device might use the decimal (d), hexadecimal (h), or octal (o) address format see the register table at the bottom of the dialog box for bit tags, append the bit address without the bit separator the lowercase letters in the address format indicate how many digits you should enter in the bit address tag formula enter a formula for the tag to process the generated data two variables are permitted value (current tag value) and timestamp (current tag unix time in milliseconds) the following math functions are available sin cos sqrt tan power power( x ) performs the operation 10^x log log( x ) is the natural logarithm (the logarithm is in base e ) exp exp( x ) performs the operation e^x only publish on change of value select the checkbox to only publish nats messages when the value parameter changes to a new value change of value only applies to boolean, numeric (such as int or float), and simple string data types it does not apply to complex types, such as json or array poll once topics will not be affected by change of value settings these topics will still only see a single message meta data metadata summarizes basic information about data this feature allows you to define key value pair data for the device output payload later on metadata can then be used to find, use, and reuse particular instances of data note if you use special characters in meta data key names, the special characters are replaced with underscore characters in the payload this can cause two key names to be combined into one for example, configuring the key names a b and a&\&b will cause only one key name to be created (a b)