Mitsubishi Q06 Serial (Gen1.3)

review the following information for setting up and configuring the mitsubishi q06 serial (gen1 3) driver litmus edge compatible series compatibility parameter compatible items driver type serial validated devices/series melsec q to set up and configure this device in litmus edge, you will need to do the following step 1 set up and configure the plc device step 2 set up the plc device in litmus edge devicehub step 3 configure the list of registers step 1 set up and configure the plc device record the serial communication parameters for the device otherwise, use plc software on your machine to look up these parameters you use these parameters for setting up the driver in the next step step 2 set up the plc device in litmus edge devicehub configure the following parameters when you connect a device docid\ pal6abpzbrimdu9lvgj30 with this driver update default values to the specific setup of your device parameter value type mitsubishi driver mitsubishi q06 serial (gen1 3) communication port local serial connection file path data bits 8 baud rate 115200 parity even, odd, none stop bits 1 step 3 configure the list of registers when you add a tag docid\ tuy hh0gi8djvot70wroh to the connected device, refer to the following register table and tag parameters see the following additional resources if necessary organize device and tag data by using metadata docid\ mu 6j6zhi0cvchdad0w8n tag formula variables docid\ io7xgyrdvv vmpnfxoaci register table name value types address format min address max address description x bit hhhh 0 8191 input relay y bit hhhh 0 8191 output relay m bit ddddd 0 61439 internal relay l bit ddddd 0 32767 latch relay f bit ddddd 0 32767 annunciator v bit ddddd 0 32767 edge relay b bit hhhh 0 32767 link relay tc bit ddddd 0 23087 timer coil ss bit ddddd 0 23087 retentive timer sc bit ddddd 0 23087 retentive timer coil cs bit ddddd 0 23087 counter contact cc bit ddddd 0 23087 counter coil sb bit hhh 0 2047 special link relay s bit dddd 0 8191 step relay dx bit hhhh 0 8191 direct input dy bit hhhh 0 8191 direct output ts bit dddd 0 2047 timer contact sm bit dddd 0 2047 d word ddddddd 0 4212735 data register zr word ddddddd 0 1042431 file register z word dd 0 15 index register sw word hhh 0 2047 special link register r word ffddddd 0 313767 file register cn word ddddd 0 23087 counter current sn word dddd 0 23087 retentive timer tn word ddddd 0 23087 timer current value w word hhhh 0 25983 link register d bit word ddddddddd 0 421273515 data register bit zr bit word ddddddddd 0 104243115 file register bit tag parameters name select a register name from the drop down list the available options depend on the names in the register table value type select a data type from the drop down list the available options depend on the register name selected polling interval enter a value in seconds this determines how often the tag should poll the register for data tag name enter a name for the tag description (optional) enter a description for the tag address enter a tag address the value must in the decimal format, within the allowed min/max range omit the leading zeros the device might use the decimal (d), hexadecimal (h), or octal (o) address format see the register table at the bottom of the dialog box for bit tags, append the bit address without the bit separator the lowercase letters in the address format indicate how many digits you should enter in the bit address tag formula enter a formula for the tag to process the generated data two variables are permitted value (current tag value) and timestamp (current tag unix time in milliseconds) the following math functions are available sin cos sqrt tan power power( x ) performs the operation 10^x log log( x ) is the natural logarithm (the logarithm is in base e ) exp exp( x ) performs the operation e^x only publish on change of value select the checkbox to only publish nats messages when the value parameter changes to a new value change of value only applies to boolean, numeric (such as int or float), and simple string data types it does not apply to complex types, such as json or array poll once topics will not be affected by change of value settings these topics will still only see a single message meta data metadata summarizes basic information about data this feature allows you to define key value pair data for the device output payload later on metadata can then be used to find, use, and reuse particular instances of data note if you use special characters in meta data key names, the special characters are replaced with underscore characters in the payload this can cause two key names to be combined into one for example, configuring the key names a b and a&\&b will cause only one key name to be created (a b)